T pe connector pipe major price

t pe connector pipe, the most common pipe fittings, are used to mix or split fluid flow. It is available with feminine sockets, solvent welding sockets or opposite solvent welding sockets, and feminine socket sockets. t pe connector pipe can attach pipes of different diameters to each other or change the path of the pipe or both. Available in a variety of materials, sizes and finishes, and can also be used to transport two liquid mixtures. [More explanation is required] With the most common equations, they may be equal or unequal along the three joints.

What are to most used t pe connector pipe?


In a knee joint plumbing system, most joints are used. The use of the knee makes it easy to change the direction of the tube. The knees are available in two types: 90 degrees and 45 degrees, although they can be cut at any angle. The knees are produced in two types of short radius and long radius.
90 degree knee

The 90 degree angle changes the direction of the pipe 90 degrees and there are two types of long and short radius.
45 degree knee

The knee is rotated 45 degrees between the two tubes and changes its direction 45 degrees.
Knee long radius

At a long radius knee, the radius of the knee is 1.5 times the nominal diameter of the tube. A high-radius knee is usually used in systems that have a lower pressure drop. Also, the knee of the long radius takes up more space than the knee of the short radius.
Knee short radius

The knee has a short radial radius equal to the nominal size of the tube. A short radius knee is used where less space is needed. This type of knee has a higher pressure drop due to a sudden change of direction in the tube.

Knee short radius
Knee Conversion

The replacement knee is used to change the direction and size of the tube at the same time. The conversion knee makes fewer connections to the plumbing system. In addition, changing the pipe direction simultaneously with its size reduces the turbulence and turbulence effect of the current and also reduces the corrosion caused by the turbulence. These features prevent a sharp drop in pressure on the line.
Bend or bend

Large-radius knees are known as bends or bends, and are less compressive due to the gradual change in pipe and the larger radius. These knees have a radius equal to 3D or 5D and are available where D is the diameter of the tube. The knee is not a standard type of joint and is made of tubes. Usually these types of knees are made in large sizes because the cost of knees in large sizes is very high. The use of hand-knees is done on low pressure water conveyors. These types of knees can be manufactured from welding 2, 3 and 5 pipe sections as shown in the types of welds.

180 degree knee U-TURN

The 180 ° knee is used to change the 180 ° direction of the tube. This type of knee is produced in two short and long radius patterns. This type of knee is used in heating coils, heat exchangers and tanks. 180 degree knee production is far more expensive and sometimes 2 knees 90 are used in place of the U-TURN.

There are three ways to split and use the main line fluid. The tee is a small section of pipe with a 90-degree bent at its center. There are two types of plumbing used in the pipeline, namely equal and inequitable three-way.

Three equal ways

In three ways the diameter of the branch is equal to the diameter of the main pipe or header.
Three ways of conversion

In three-way conversion, the diameter of the branching is smaller than the diameter of the main line. The branching of this type of triangle has an angle of 45 degrees or an angle of 90 degrees. The Wye Tee allows the tube to connect to another tube at an angle of 45 degrees. This type of three-way reduces friction and perturbation that may hinder the flow of motion and is also known as a lateral three-way.


Intersections or Intersections An intersection has one input and three outputs or vice versa and is usually not used in process pipes for fluid transmission. But the forged fours are commonly used in the Sprinkler fire system.


Converts the size of the tube. Conversions are produced in two types:

Concentrate conversion
Decentralized conversion

Concentric or conical conversion

In the center cone or cone shape the axis of both ends of the transform is in a straight line. This type of conversion keeps the central axis of the tube at a constant height. This type of conversion is used when the central axis of the large tube and the small tube are kept at the same height.

Concentric or conical conversion
Decentralized conversion

Decentralized conversion is the axis of the two ends of the conversion at different altitudes. Holds the asynchronous conversion of the low-altitude pipe (B.O.P) on one level. Decentralized conversion is used when one of the pipe surfaces must be kept at a constant height. The offset created in this type of conversion is equal to the diameter of the two tubes.
SWAGE conversion

SWAGE conversion is produced in small sizes and is used to connect tubes to smaller gear tubes or silencer tubes. This type of conversion exists in both non-center and non-center types. Both ends of this conversion can be flat or ribbed, or one end of the bed and the other end ribbed. This type of conversion is used in high pressure systems.


The cap covers the end of the tube. The pipe cap is used to blind the piping system. In some applications, the cap is used to create a waiting line and continue piping in the future.
Threaded nut joints

An alternative replacement nut nut is used for flange connection in low pressure and small size systems where pipe and equipment open and close are more common than usual. These types of joints can be either gated or silent. Masaurus’s vertebra consists of a male, a pistil and an intermediate vertebra.

t pe pipe options

In many applications, polyethylene plastic pipes can be a good replacement for steel pipes. Recent estimates show that only 5% of the costs spent on developing metal pipe systems are sufficient to set up plastic PE networks. Of course, in many of these systems, plastics alone do not work, and the role of metal valves cannot be ignored. Studies have also shown that polyethylene pipes, especially those of high density (high density HDPE), are more efficient than steel pipes and have a wide range of applications. It has been tested and proven in a variety of locations such as land surface, buried, floating, and submarine surfaces. In addition, these pipes are also suitable for the transport of drinking water, sewage, chemicals, slurry, hazardous waste and compressed gases. . Continue to partner with Tosun Sanat Apadana in producing and supplying all kinds of PE pipes, irrigation pipes, irrigation strips and pipes to compare more PE pipes and steel pipes.and also we can have t pe connector pipe cheap.

Compare some of the most important features of PE pipes and steel pipes
Environmentally friendly

There are no adverse environmental effects in the production and use of polyethylene pipes. These tubes are also resistant to invasion by microorganisms because polyethylene is not a nutrient for them. Therefore, polyethylene pipes are considered as suitable pipes for environmental protection. However, due to the combination of oxygen with air and the corrosion of steel pipes, these pipes can damage the environment.
Resistance to chemicals

The structure of polyethylene is simpler than that of all commercial polymers. A polyethylene molecule is made up of a long chain of carbon atoms with two hydrogen atoms attached to each carbon atom. Polyethylene, which has a small number of side chains and is short in length, is called heavy polyethylene, or linear polyethylene. In this case, there is no branch in the molecule. Linear polyethylene is harder than branched polyethylene, but branched polyethylene is made easier and cheaper.

Light and heavy polyethylene have quite different properties and applications, so they can be assumed from two separate families. But in general, polyethylene pipes have significant resistance to organic and inorganic chemicals. Engineering and environmental research at the University of California, Berkeley, shows that steel pipes are generally not resistant to chemicals and need to be reinforced. However, polyethylene is resistant to chemicals.
Tensile strength

Polyethylene pipes have greater tensile strength than steel pipes and break easily when pressed internally and externally, but polyethylene pipes are molecules when subjected to constant load pressures for a long time. Pipes allow for separation and release, which reduces the stress required to deform and prevent failure. The chemical components present in the raw material of PE pipes can withstand further creep before rupture, which increases the scope of their applications for underground projects with the risk of ground displacement or inadequacy.

Where to find t pe connector pipe catalogs?

We can provide catalogs of how to connect polyethylene T-pipes from various sites such as the site of the manufacturer of PE pipes and can also be accessed through the factories themselves. It is related to the same product because these products are distinguished by the diameter and the volume of the pipe.

Is t pe connector pipe good?

Testing the car under the tire and passing it is incorrect and does not prove quality. Professionals can comment on the quality of the pipe by dropping the pipe on the floor and listening to its sound. Polyethylene pipe should last several years under direct sunlight. One of the most important hallmarks of pipe quality is that it boils properly and that its boiling life is maintained for many years. The smooth and smooth surface of the tube also indicates its quality. Also, the PE pipe should never be brittle and dry.

In general, the following benefits to the general public of plastic pipes are as follows:

1. Corrosion resistance:

pipes do not corrode most of the chemicals found in domestic wastewater
and also have minimal resistance to the passage of other wastewater and
other fluids due to the smooth surface. These pipes will never rust and
will not corrode.

2. Lightness and ease of transportation:

addition to ease of transportation and cost reduction, in the case of
plastic pipes, cutting, joining and installation are much easier than
other types of pipes such as metal pipes.

3. Flexibility and toughness:

in underground applications, the flexibility of plastic pipes reduces
the number of connections and easily curves piping paths.

4. Various connection methods:

general, plastic pipes have the ability to thread, flange, heat weld,
glue, compressor, etc. and provide a wide variety of connections for
different conditions.
5. Excellent Hydraulic Properties: Plastic
pipes fall into the group of flat surface pipes, which results in the
least energy required to transport various fluids.

6. Lower life and cost of installation and maintenance:

pipes have been used in most cases for more than 22 years and have not
yet reached the end of their life. On the other hand, they cost less
during the purchase period due to lower purchase, installation and
maintenance costs. Useful. Limitations The first major limitation of
plastic pipes is their strength and low rigidity. In the next step,
these pipes are sensitive to high temperatures.

An Overview of the Benefits and Disadvantages of Plastic Pipes Overall Properties of Polyethylene Pipes

1. Resistance to rapid crack propagation

of the desirable goals of design is to avoid the possible occurrence of
rapid crack propagation (RCP) in the pipe, as the consequences of such
an event can be very serious, especially when flammable materials are
transported through the pipe. However, even when transporting inert
substances such as water, defects such as RCP cause a large amount of
fluid in the pipe and cause extensive damage to the pipes and joints.
popular feature of PE pipes is that they leak before they break. This
is a result of the high strength and toughness of these materials.
However, the strength of PE decreased with decreasing temperature.
factors that increase the likelihood of RCP occurring include: fluid
type, compressible or incompressible (, increased pipe diameter,
increased pipe wall thickness, and increased working pressure). The
proper installation and operation of polyethylene pipes that are welded
together are very likely to cause RCP, in fact the RCP is much less
likely to occur for PE pipes than other thermoplastic pipes. Conditions
of pipe material, pipe parameters and performance parameters to prevent
the possible occurrence of RCP are very complex. That is still under

2. Wear resistance

Polyethylene pipes are regularly
used today to transport granular or slurry solutions such as sand, fly
ash and coal. The advantage of polyethylene pipes in this application is
the high resistance of pipe coatings, for example in experiments it has
been shown that this resistance is 1 to 2 times higher than that of
steel pipes when transporting fine grains. Polyethylene pipes have
elastic properties that, under the proper conditions of fluid flow,
cause particles to jump from the surface of the pipe wall. This feature,
combined with the strength of the PE, creates a useful life in the
tube, which is longer than many metal pipes.

3. Expansion / contraction coefficient

or decreasing the temperature causes it to increase or decrease
correspondingly along the tubes that are not inhibited by movement. Also
in the case of pipes that are restrained against movement, these
temperature changes lead to the formation of longitudinal or compressive
stresses in the pipe. In order to properly install, design and operate
polyethylene pipeline systems, both expansion / contraction events
should be considered carefully.
To take.
One of the features that
distinguishes polyethylene pipes from metal pipes is that the thermal
expansion coefficient of polyethylene pipes is 11 times larger than
steel pipes. This means no more expansion / contraction in the tubes.
However, another disadvantage of polyethylene pipes is that of metal
pipes, having much less elastic appearance than polyethylene pipes. In
restrained pipes, this results in a lower level of longitudinal stress
due to heat, which in turn reduces the need for retainers and hooks.

4. Chemical Resistance

are some of the effects that various types of fluids have on the
long-term hydrostatic strength of raw materials for PE pipes, and the
degree of reduction (if any) required to observe these effects:
solutions of salts, acids and bases Since polyethylene is not immune to
electrolyte attack, these solutions have no adverse effect on it.
Accordingly, water-based design can also be used for such materials.
and wastewater, usually, do not have components that affect
polyethylene. Therefore, water-based design is also used for such

agents such as detergents, alcohols and glycols, including antifreeze
(if such agents are present in the fluid being transported, should be
warned to use a type of polyethylene pipes that are resistant to raw
materials. They are very resistant to slow growth of cracks, and for
such raw materials, there is no need to lower the temperature compared
to ordinary water.
Fluids containing oxidizing agents gradually
degrade strong oxidants of polyethylene materials. The rate of this
failure depends on the concentration and level of chemical activity of
the oxidizing agent. If the failure rate imposed on unprotected
polyethylene is slow, it can be made of polyethylene pipes that are
sufficiently antioxidant
Have used. But if the song is fast, it is
better not to use PE pipes. Therefore, the suitability or inadequacy of
the use of PE or the degree of reduction that should be applied should
be investigated on a case-by-case basis.
Neutral gases such as
hydrogen, nitrogen and carbon dioxide, these gases do not have any
adverse effects and water-related design values ​​can be applied to
Low molecular weight gaseous hydrocarbons, such as methane and
hydrogen sulfide, have long-term studies and experience showing that the
long-term strength of such gases is at least equivalent to the
long-term strength of air or water. So there is no need to reduce the
Vapors produced from liquefied petroleum gas consist of
slightly higher molecular weight gases. These gases, due to their
softening effect on PE, result in a slight decrease in long-term
hydrostatic strength of PE. In this case, water pressure reducing
coefficients for water pipes are commonly used. Conventional
hydrocarbons in liquid state, such as those in liquefied petroleum gas
and gas condensates, in crude oil, in gasoline, in diesel fuels, and in
petroleum oil, since exposure to such liquids have a greater softening
effect. The practical solution in these cases is to either reduce the
degree of polyethylene pipes over vapors, or use pipes of a different

weak points

– Need protection against the effects of UV
– Resistance decreases with time and intensifies with increasing temperature
– Weakness against suction created in the tube
– Impact of petroleum and some chemicals such as alcohols, halogens and aromatics on these pipes
– Unable to detect buried pipes in trench with metal detector
– Ability to make deep scratches and cuts at the pipe surface when transporting and installing pipes
– Some joints should be made of high pressure pipes and have thickness differences with the main pipe.
– Extreme thickness increase at high operating pressures

Delay due to the transfer of chlorine-containing waters and decrease
their lifespan Comparison of polyethylene pipes against PVC pipes

PVC pipes do not spread the flame due to fire, they burn and burn only
at the point of fire, but if polyethylene pipes fire, they spread on
– PVC pipes emit toxic gases when burning.
– PVC pipes
become extremely brittle at temperatures below zero degrees Celsius, but
polyethylene pipes also exhibit tough behavior at these temperatures.
– In rock and rock containing terrain, PVC pipes have less seismic resistance than polyethylene pipes.

The simpler connections of PVC piping systems than polyethylene, in the
figure below, are connected to the right of the PVC pipes and to the
left of the polyethylene pipelines.
Polyethylene pipes are more resistant to buckling during installation or installation due to their high flexibility.
– PVC pipe connection is more polluting and less reliable.
– It is easier to repair polyethylene pipelines.

Wholesale distributors of different t pe connector pipe

Factories are the main and first sellers of polyethylene pipes in the country. Manufacturers have to be able to sell it after they produce polyethylene pipes, so they set up their own dealerships by creating dealers. But if one wants to buy t pe connector pipe bulk at a lower cost, one can buy one-inch polyethylene pipe directly from the factory. The purchase price of the branched PE pipe as well as the 5 layer PE pipe is lower than the market and the buyer can buy more pipe from the factory.Factories can make only t pe connector pipe for export becaus of it benefits.

Given that the price list of PE pipes is updated daily and the prices are not the same in different cities, you can use the following methods to find out the wholesale price of one inch polyethylene pipe in the market to find out the day price of PE pipes. Get ethylene.

Search the internet and the sites for selling PE
Visiting stores, dealers and major PE stores
Refer directly to the factories producing this product in the country

Polyethylene pipe is a high quality product used in the water supply industry both inside and outside the cities and villages. One of the ways to sell this item is on the internet sales market. The polyethylene pipe is supplied online at varying pressures and thicknesses, and buyers can order the amount of pipe they need and order it at the desired location as soon as possible.

t pe connector pipe manufacturers list

Giti pasand Group (Azin Tube, New Pipe, Newflex)
– Azin pipe:

One of the well known brands of polypropylene pipe and fittings in Iran is Sepahan Azin Tube Company. The brand, along with Newpeep and Newflex, are among the subsidiaries of Isfahan’s renowned Giti-Pasad Company.
In-tube products are offered in different types of polypropylene pipes and fittings (PP-RC), in two groups of single and three layer pipes and two colors of green and white in domestic and foreign markets.
Azin Tube Sepahan Company using the knowledge and machinery of the world has made high quality products that have been able to obtain many endorsements and standards.
Three layer pipes is one of the unique and high quality products of Azin Tube Sepahan Company which are the new and advanced generation of single layer pipes. Reducing the longitudinal expansion coefficient and preventing the penetration of oxygen and light, long life span and no apparent deformation during hot water flow are the special features of the five-layer pipes used in the hot water piping industry.
Receiving Partner Laboratory Certification (Standard Accreditation) from National Standards Organization of Iran, the only UK certified health company, ISO certified from Germany, EU and Russian product compliance certification, are a small part of the Azin Tube Sepahan Company’s honors. Can prove the quality and efficiency of its polypropylene t pe pipe wholesale products and fittings.

– Newflex:

Newflex, one of the three subsidiaries of Campus Spadana Company, is a brand of Isfahan-based Gate-friendly Esfahan, which launched its 84fit pipe and fittings products in the name of Newflex.
Push Fit is a type of modern sewer pipes and fittings that have been used in many countries around the world due to their high strength and safety. The main ingredient in Fit Coating is polypropylene called PP which is the best choice because of its unique formula for transporting all kinds of chemicals, toxins, hot and cold wastewater. Therefore, most pipe and t pe connector pipe in USA consumers prefer fittings to polycarbonate.
Fit Newflex Pipe and Pipe Fitting products are available in 4 categories, Fit Pipe Group B, BD Group, Silent Band and Sewer wall cladding in Active Fit Newflex Pipe Fittings and Fittings.
One of the distinctive features of Newflex products is the use of a
t pe connector pipe for seal ring in the form of a grooved rubber gasket compared to other wear products. This makes it easier to attach and install, in addition to increasing resistance and preventing glue problems.

– Newpeace:

Newpipe is another brand of triple pipe and fittings company in Isfahan which includes five layer pipe and joint products of this company.
New Pipe Tubing and Connection are made using the best of the most up-to-date devices and are considered one of the first and most famous brand of five-layer inner tubing and t pe connector pipe in 2019.
High strength, high pressure tolerance and 90 ° temperature, minimal pressure drop, safety, hygiene and reasonable price are the most important features of pipe and joint of five layers of nippe.
Many certifications and standards, including technical certification from the Building and Housing Research Center and the Standard Organization, ISO 9001: 2015 and BS OHSAS 1881: 2007, etc. all demonstrate the high quality and quality of Newpeipe products.
Newpipe products are widely used in all types of water transfer systems, cooling and heating systems, hot and cold water piping, floor heating and ventilation.
Types of five-layer press and pipe fittings, 5-layer fittings and five-layer pipe presses, as well as special coupling and press fittings have a 5-year corporate guarantee and 10-year insurance.

Materials used in t pe connector pipe production

HDPE Tube is a type of flexible plastic pipe that is used to transport liquids and gases, and is often used to replace old concrete or steel pipelines. Made of HDPE (High Density Polyethylene) by heat, high impermeability and strong molecular bonding, which makes it suitable for high pressure pipes. HDPE pipes are used worldwide for applications such as water network, gas network (self-launched sewage source), slurry transmission lines, rural irrigation, fire fighting system supply, electrical channels, communications, storm and drainage pipes. .