Polyethylene irrigation fittings are one of the most widely used fittings in high pressure irrigation in the agricultural industry and are used for sealing and pipe safety, water flow regulation, pipe size change and flow direction change. Irrigation fittings include all types of fasteners, knees, converters, tees and hose heads and are manufactured and used in a variety of sizes and in different thicknesses for a variety of pipe sizes.Produce irrigation pipe fittings from the centers of these products.
Is it good to use plastic pipe fittings for irrigation?
Irrigation refers to all the ways in which water is drained with little to about 1 to 10 liters per hour and slowly discharged near the plant. For this reason, this method of irrigation is known as low volume irrigation. Irrigation is the slow flow of water over the surface or under the soil in the form of separate, continuous droplets, a thin stream or fine spray through droplets along the water line. Drip irrigation has many methods and concepts such as drip irrigation, in-bed irrigation, fountain irrigation and spray irrigation.
In irrigation, water is distributed in a pipe system in the field, and the mechanical device or device from which the water is sent out to the plant is called the outlet or emitter. The outflow of water from the emitter can be in the form of a drop, a bubble or a continuous small stream. Even the player can be a very small sprayer.Today, with the increase of the irrigation population in agriculture, it is of great importance. The use of polyethylene pipes for irrigation of agricultural land, farms and greenhouses has greatly increased, but needs to be assured of its efficiency and advantage. Water input to agricultural land is an important issue for farmers because if high-pressure water enters the land and becomes concentrated at one point, it will cause crop failure and delay production. Therefore, proper plumbing should be done to minimize irrigation problems and increase production. Polyethylene pipe provides a great solution.13mm irrigation pipe fittings are used in many agricultural industries.
Installation of a large drainage system ensures that the water is fast and efficient, helps reduce soil erosion and compression, minimizes rupture in equipment, plantings grow with healthy roots and perform all seasons. To be. Gradually, with the increase in land productivity and the sale of more and more quality products, all drainage costs and so on will be offset.
Given the increasing use of plastic pipes in industrial plants and buildings in the country and the production and distribution of different types of plastic pipes under different names as the petrochemical industry develops, choosing and buying the best and most suitable type of pipe Plastic is not easy for a particular application and requires studying and understanding the common types of these pipes.
Types of Plastic Pipes This set of advantages and disadvantages of plastic pipes is presented and the reader is introduced to the most common types of plastic pipes used in the installation industry and their applications.
Various types fo irrigation pipe fittings on the market
Drip irrigation is required for polyethylene pipe products, irrigation pipes, irrigation strips and ad hoses.
The water source is the central control station (including pumping station and filtration station) where the pumping station itself includes the pump and its accessories and the filtration station uses either a cyclone or a sand filter (depending on the type of water source used, one of these two types of filters). Are cyclone or hydrocyclone filters for water wells, and sand filters for water storage pools), fertilizer tanks, mesh or disk filters (disk filters absorb smaller particles than mesh filters), main pipes, water pipes, pipes Side or side pipes (laterals), emitters and fittings required
Central Control Unit: It consists of devices that pump the pumped water after treatment and increase the fertilizer (if necessary) with precise control of the flow rate and pressure regulation into the main irrigation pipe.
- Relaxation Pool (if required)
- Sand filter
- Fertilizer tank
- Grid filter or disk filter
Drip or topical irrigation refers to a variety of methods of pressurized irrigation, in which water is delivered directly to a small area near single plants by dropper or sprinklerers stationed along a water distribution line. In each fruit or vineyard there is one or more sprinklers for each tree.
For row crops (such as cauliflower, lettuce, pepper, cotton) and crops (alfalfa, legumes), the water dispenser is located close enough to the plant to provide the capillary force of soil water to the root range of each plant.1 inch irrigation pipe fittings and 2 inch irrigation pipe are used in agriculture.
It is not common to use emitters for crops that are spread all over the farm due to the difficulty in humidifying the whole farm and the low price of these crops.
In fact, in a drip irrigation system, water is pumped to the ground near the root zone of the plant to soak a small area and depth of soil surface. The system was originally designed for a situation like fruit gardens where trees are too far apart. After drip irrigation proved to be a success for fruit trees, it was also applied to row crops.
Pipes and Fittings for Irrigation Systems at wholeslae price
Did you know that the wholesale price of drip irrigation fittings at the official dealership of these products is cheaper than other branches. Major purchases of irrigation fittings in large numbers are made for dear farmers by agricultural companies.
Polyethylene irrigation fittings are widely used in drip irrigation under pressure and in the agricultural industry. These joints can be used for sealing and safety of pipes, regulating water flow, resizing the pipe and redirecting water flow. Its drip irrigation fittings include a variety of fasteners, knees, converters, tees and hose heads. It is manufactured and used in different sizes and in different thicknesses for different pipe sizes.Types of irrigation fittings include:
- Hose head
The price of drip irrigation fittings is set in two major and minor ways by Irrigation Agriculture Company. Many centers sell these products, but shopping is definitely a difficult task to be sure.Provide Pipes and Fittings for Irrigation Systems at wholeslae price from these product centers.irrigation pipe suppliers These tubes are manufactured in various types.
What type of pipe is used for irrigation?
Today, due to the reduction of groundwater levels and the use of saline water and the optimum use of water and reducing the high costs of labor forces, agricultural experts have come to design a pre-designed irrigation system to use the least water. Use for our crops and prevent excessive water wastage and proper and uniform irrigation of our plant roots. Therefore, agricultural equipment has different types each of which is used in its own locations and at different intervals. Irrigation is used uniformly through pipes, sprinklers and emitters.Plants and crops need water to grow. Much of the water in the agricultural sector is used for irrigation.
In order to optimize water use in agriculture, different irrigation methods should be used to provide both the water needed for the plant and reduce the amount of water loss in each sector.
Nowadays, with the advent of technology, traditional methods have gradually been abandoned and new methods of irrigation have been replaced.One of the methods used today for optimum use of water in agriculture is the use of polyethylene irrigation pipes that are marketed in various sizes and sizes. Introduction to polyethylene irrigation pipes:
- 10mm polyethylene pipe
- 16 mm polyethylene pipe
- 32mm polyethylene pipe
- 50mm polyethylene pipe
In a pressure irrigation system, water is delivered to the surface via high pressure pipelines and network connections. In this way, the water loss is very low as the water is in a closed environment all the way.
In high pressure irrigation different pipes are used with different materials:
- Polyethylene pipes
- Asbestos Pipe
- Plika tube
- Aluminum pipe
- Galvanized pipes
Among the types of pipes used for pressure irrigation, polyethylene pipes are the most used.agricultural irrigation pipe fittings are very diverse.Drip irrigation is a method in which low-pressure water is pumped to the plant through a device called a dripper. Drip irrigation is also called low volume irrigation.
The drip irrigation system consumes less water than other irrigation methods. It uses a lot of equipment. One of the main equipment used in the drip irrigation system that is used to save water is polyethylene pipes which are used in various dimensions.The best polyethylene pipe used for drip irrigation is a 16 to 40 mm polyethylene pipe.However, many factors influence the type and size of polyethylene pipes used in drip irrigation.The type of soil, the area of irrigation, the temperature and humidity of the environment are factors that influence the size of the PE pipe.Pipes used in drip irrigation can be made of pvc or asbestos. But these pipes are rarely used.
What is the best fitting for PVC irrigation pipes?
When it comes to agriculture, one of the first things that comes to mind is the water transportation system for irrigating crops. There are many options available for the plumbing system. The reasons we use PVC pipes are as follows:
- PVC pipes are durable.
- PVC pipes perform better at abrupt pressures than flexible polyethylene pipes.
- Under the right conditions they can work for over 100 years without replacement.
- The price of PVC pipes is relatively cheap.
- The last reason is that PVC pipes are available in different sizes. This includes different thicknesses and different sizes.
- Flexible PVC pipes have the flexural strength to bypass roots or trees in irrigation or other outdoor applications.
Another very important aspect of PVC is that they are less dependent on their raw materials. Hundreds of types of PVC pipes and fittings are available to farmers, meaning you can order exactly what you need.
As mentioned before, one of the main reasons for using PVC pipes is cost saving and water conservation. The cost of shipping and maintaining PVC pipes is relatively cheaper. PVC pipes are exposed to chemicals such as fertilizers and pesticides. Also, the PVC pipes are strong enough to avoid damage to the shovel.A drip irrigation system is implemented for small to medium sized gardens. In this method a droplet is placed for each plant to prevent water loss. The PVC equipment used in this method is very inexpensive and economical, and because of the continuous drainage system, because of the high resistance of these pipes and their durability, the use of these products in drip irrigation would be quite economical.
Replacement of PVC components in drip irrigation is also quite practical and easy due to simple replacement.
Suppliers and dealers of Iranian irrigation pipe fittings
Sales of irrigation pipes and fittings are now on the websites of these products. These types of fittings can be different depending on the brand and quality, so they are available in both internal and external types, with a quality interior manufactured in accordance with internationally defined standards. Polyethylene pipes and fittings are easily fitted and are priced according to variable quality.Watering & Irrigation Supplies on Sale is done by the centers of these products.Suppliers and dealers of Iranian irrigation pipe fittings sell this product in various types.Irrigation suppliers are abundant throughout the city.
Watering & Irrigation Supplies on Sale
Prices for irrigation pipes and fittings can be found on various websites. These types of joints are available in a variety of packages, pipes, knees, converters, tees and hoses and are used to regulate water flow and sealing and pipe safety, pipe resizing and flow direction.
These fittings and pipes are available in different types with different load classes such as Class 4, 6,8, 10 and 12 and a half atmospheres and are also high pressure fittings. This product has been resistant to ultraviolet and solar rays because it has been exposed to sunlight for a long time and may affect its quality and longevity.
The sale of irrigation pipes and fittings in bulk and in Aria agricultural equipment is possible with a special discount. Irrigation fittings are one of the most widely used fittings in pressure irrigation and can be used for sealing and safety of pipes, water flow regulation, pipe size change and flow direction.microbore irrigation pipe is one of the different types of this product for sale.
Polyethylene drip irrigation pipes and fittings are the most commonly used in high pressure irrigation fittings and have long been exposed to sunlight and may affect their quality and longevity. They are resistant to ultraviolet and solar radiation. These pipes have high chemical resistance to rot, rust, corrosive materials, chemical fertilizers and their mechanical resistance to pressure and impact is high.