Posts

Shopping Center of Drip Irrigation Fittings in Iran

Sales of drip irrigation fittings compared to sales of irrigation pipes. It has its own conditions. For example, fittings have a large number of devices and a wide variety of fittings, as well as different types of fittings for which these particular conditions of sale apply. Sales of drip irrigation fittings should be in accordance with the type of need, type of pipe, pressure. If you want to make a list of pre-prepared drip irrigation accessories for sale, it’s a far cry from the wide variety of work items and the constant price changes. Follow us on to provide you with the complete drip irrigation fittings catalogue.

Shopping Center of Drip Irrigation Fittings in Iran

Famous Suppliers and distributors of irrigation fittings

Famous Suppliers and distributors of irrigation fittings

The factory for the suppliers and distribution of irrigation fittings can vary depending on the type of connections they produce. But no matter what type of connections are produced, the plant must be clean, tidy and fully optimized, with safety considerations in place to ensure the safety of device operators. The plant for the suppliers and distribution of irrigation fittings should be considered as a place for storing raw materials where the raw materials are stored safely and regularly.

The drip irrigation fittings connectors plant is better qualified to have obtained the ISO18001 Occupational Health Certificate and ISO 14001 Environmental Certification from a reputable institute in accordance with the most recent revisions of the ISO, and HSE rules must be observed in the factory environment.

Production lines for irrigation fittings If there is a type of Poly material to be imported as raw materials, there should be silos for storing raw materials to feed the equipment alongside the production lines and machines.

irrigation fittings have a high percentage of waste production, especially manufacturers and distributors of injectable fittings, as well as machined fittings such as poly flanges which are shaved from a molded sheet. To ensure that these wastes are not combined with the approved end product, the final product is 100% reliable.

The injection molding plant puts the injection devices side by side and feeds the raw material feed pipes through the silos, and in this system and method of production, the irrigation fittings are used as raw materials. High pressure injection injectors (up to 250 bar), poly screw joints and electro fusion joints are all manufactured by injection machines.

Miter fittings and custom irrigation fittings are used as raw materials. In these factories, irrigation fittings pipes are first divided into required parts and eventually made by different types of welding machines and the required fittings are produced. If the fittings manufactured by Maitree are of the irrigation fittings type of poly used in the project, the best type of PE will be of high strength and more resistant to the pipe.

The irrigation fittings factory must be equipped with a quality control laboratory. The quality control laboratory must have a 17025 certification and other required standards, use appropriate equipment and up-to-date laboratory personnel and engineers and technicians.

The fitting plant is not just about producing and testing the product and one of the most important parts is packing and transporting poly to the customer site and project site. The joints shall be packaged in such a way that they do not interfere with each other and shall be handled with care so that the outer body and edges of the joints are not damaged and the carton should be packed where possible.

Small injectable joints and screw joints are packaged in cartons because of their small size, which is convenient and safe, but conventional and large pressure and high pressure joints cannot be considered conventional packing. They wrap around large irrigation fittings joints and connecting heads with bubble liner and glue on regular pallets and laths as regularly as possible and fasten to secure them in place.

Newest wholesale price range of drip irrigation fittings

The price list for drip irrigation fittings includes the following types of fittings:

  • Injection fittings price
  • Price of custom high pressure fittings
  • Price of sewage connections

Note that buying cheap, and especially cheap, is not a good purchase and is not a good quality product. In the case of polyethylene products and PE irrigation connections, the price of these fittings should not be lower than the PE price list. Because all standards clearly state that new raw materials should be used.

The price of irrigation fittings on the price list is the lowest among pipe fittings, and these fittings are mostly used for normal applications and low operating pressures such as irrigation, injectable irrigation fittings often with low-grade polyethylene materials (not Iranian materials and materials). Are produced and processed in such a way that there is a possibility of a problem in their tissue. There is also a price list for irrigation fittings and their vendors produce them in a pre-determined schedule and have depots in their warehouses, making it easier to obtain and deliver, and are more stable.

Price of custom high pressure irrigation fittings:

  • The price of custom fittings is directly related to the price of irrigation pipes. For example, Miter fittings are made of the same type of PE pipe as with the same raw material that the pipe is made. Due to the above description, custom high pressure irrigation fittings prices cannot be provided as fittings price lists and applicants must submit a list of fittings required for the unit of sale and receive prices after calculation along with delivery time.

Various types of drip irrigation fittings on the market

Various types of drip irrigation fittings on the market

The connections are simple and practical, all of which can be easily assembled and installed without any special high-speed tools. Drip irrigation pipes and fittings are so simple that even with very little expertise with a bit of training, the plumbing can be run just to give it a little taste and a small investment that will soon be offset. Prevent excessive use of water and have a lush garden and a farm or tree full of crops.

Irrigation fittings are mainly 2mm in diameter including knee, three way, interface, 1mm primary pipe connection, primary washer, type to type interface and so on. Drip irrigation connections are very simple, inexpensive, lightweight and affordable. Increasing the use of drip connections between farmers will help greatly save water consumption.

A drip irrigation system is unique because of the effective use of water and the directive power of agronomic, agrotechnical and economic benefits. The drip system consumes only half of the water needed for sprinkler or surface irrigation. In drip irrigation, water is pumped from a low pressure pipe network into a predetermined pattern. The device for entering water into the soil is called a dropper. Droplets through a narrow nozzle or long flow path reduce the pressure in the pipe network and reduce discharge discharges by approximately 1 or 2 liters per hour.

Drip irrigation fittings including:

  • Smart drip irrigation
  • Dripper on the line
  • Type Bar

Poly Fittings & Accessories on Sale

A variety of accessories and fittings are used for a variety of purposes, most notably in agriculture, which are used in drinking water networks, municipal wastewater and agricultural irrigation networks. One of the most important advantages of poly pipes is their easy connection to other pipes. Poly fittings are usually used to maintain pipe lengths, pipe path shifts, track angle changes, and so on.

Poly tubing fittings pipelines and virtually all pipelines, regardless of their gender, require poly fittings. Classifieds of poly appliances on my land site as poly connectors, poly way, belts, polyethylene pipes, caps, all kinds of poly valves (automatic valves, solenoid valves, air valves …), interfaces. Applying poly fittings to the paths of the irrigation pipes, in addition to the ease of moving the pipes along the different paths, also increases the efficiency of irrigation. Dear customers and farmers, depending on their irrigation system and system requirements, they can purchase any of the bridge connections from my site.

Irrigation & Watering Product catalogue for buyers

Irrigation & Watering Product catalogue for buyers

In order to optimize water use in agriculture, different irrigation methods should be used to provide both the water needed for the plant and reduce the amount of water loss in each sector.

Nowadays, with the advent of technology, traditional methods are gradually being abandoned and new methods of irrigation are replaced.

One of the methods used today for optimum use of water in agriculture is the use of polyethylene irrigation pipes that are available in different sizes and sizes.

 Introduction to poly drip irrigation fittings

• 12 inch drip irrigation fittings 

• 14 inch drip irrigation fittings 

• 16 inch drip irrigation fittings

Contact our consultants for the price of PE.

Types of PE irrigation pipes

Irrigation under pressure

In a pressure irrigation system, water is delivered to the surface via high pressure pipelines and network connections. In this way, the water loss is very low as the water is in a closed environment all the way.

In high pressure irrigation different pipes are used with different materials.

• Poly pipe irrigation fittings

• Asbestos Pipe

• Plika tube

• Aluminum pipe

• Galvanized pipes

Among the types of pipes used for pressure irrigation, polyethylene pipes are the most used.

 Pipes used in drip irrigation

Drip irrigation system

Drip irrigation is a method in which low-pressure water is pumped to the plant through a device called a dripper. Drip irrigation is also called low volume irrigation.

The drip irrigation system consumes less water than other irrigation methods. It uses a lot of equipment. One of the main equipment used in the drip irrigation system that is used to save water is polyethylene pipes which are used in various dimensions.

The best polyethylene pipe used for 12 drip irrigation fittings is a 16 to 40 mm polyethylene pipe.

However, many factors influence the type and size of polyethylene pipes used in drip irrigation.

The type of soil, the area of ​​irrigation, the temperature and humidity of the environment are factors that influence the size of the PE pipe.

Pipes used in drip irrigation can be made of pvc or asbestos. But these pipes are rarely used.

Fittings, Accesories & Piping Materials for Sale

Types of connections:

• Oil Field Unions

• Pup Joints

• Flanges

Due to the high pressure in the oil and gas drilling industry, fittings with oil industry-approved standards are used to reduce the risk of problems during operation while reducing the risk. Alloys are important drip system parts in this section. Some of the most commonly used components include the following:

• Hammer Union Types:

These joints are threaded and welded, which are usually used for high pressures Psi 5000 and for conditions where the H2S environment is higher than standard.

• Pup Joints are another type of fittings that are separated by two threaded or welded parts in two tubes of different lengths and patterns. These joints are sometimes made up to pressures up to 100,000 Psi which are at the request of the customer and as required by the consumer.

• Flange Types: Flanges are one of the most important joints in the oil, gas, petrochemical and refinery drilling industries, a type of coupling of pipes, valves and devices to each other. Flanges are disk-shaped, often coupled in two, using two bolts to attach to each other, open easily and are suitable for low and high pressures.

Flanges are fittings that connect transmission pipelines (with any type of fluid) to each other, as well as connecting valves to welded pipes. Flanges are often made of polyethylene, steel, steel, iron or cast iron alloys. The flanges are subdivided into different classes depending on the type of material, depending on the pressure they endure.

 

Blind Flange:

  • A closed plate used at the end of the piping and pressure paths. This type of flange as well as its screws generally bear more pressure than other flanges, with the maximum being at its center. Depending on the flange class it can withstand proportional pressure.

Weld Neck Flange or Welded Neck Flange:

  • The flange of the neck has a conical neck whose radius at the end is equal to the diameter of the pipe and is welded to it. This neck strengthens the flange’s tolerance. This type of flange is suitable for handling high pressures and temperatures below zero as well as vibrational and vibrational loads.

Slip on Flange:

  • This type of flange is used in regular services. It is simple to install and withstands two-thirds of the internal pressure and one third of the fatigue load of the neck flange and costs a bit more.

Lap Joint Flange:

  • It is similar to a conventional flange with no bottom layer, the end of which is bent and the tube being butt-welded at the other end. This flange has no contact with the fluid and costs more than one-third the gland flange and only one-tenth the gland flange withstands the stress resistance.

Socket weld Flange with flange welding:

  • As its name implies, the flange has a chamber in which the tube is inserted. If the flange is welded internally, its fatigue resistance is one and a half times its static resistance to the Slip on flange.

Screw Flange or Threaded Flange:

  • The threads are threaded into the flanges and the pipe can be screwed into. The advantage of these flanges is that they do not require welding. Welding can also be used if necessary and at high pressures. The performance of these flanges is at high pressures.

Orifice Flange:

  • This flange is in fact a rotary flange and, in some cases, a hinged radius. These holes are used to measure the fluid or gas flow.

All these fittings and accessories are sold on our site and you can contact our sales consultants and easily purchase all your plumbing supplies at the lowest price and highest quality.

What are the bestselling types of irrigation fittings?

What are the bestselling types of irrigation fittings?

Polyethylene drip irrigation fittings are one of the most widely used fittings in high pressure irrigation in the agricultural industry and are used for sealing and pipe safety, water flow regulation, pipe size change and flow direction change. Drip irrigation fittings include a variety of fasteners, knees, transformers, tees and hoses and are manufactured and used in a variety of sizes and in different thicknesses for a variety of pipe sizes.

Drip irrigation refers to all the ways in which the water is drained in a low volume of about 1 to 2 liters per hour and slowly discharged near the plant. For this reason, this method of irrigation is known as low volume irrigation. Drip irrigation is the slow flow of water over the surface or under the soil in the form of separate, continuous droplets, a thin stream or fine spray through droplets located along the water line. Drip irrigation has many methods and concepts such as drip irrigation, in-bed irrigation, fountain irrigation and spray irrigation.

In drip irrigation, water is distributed in a pipe system in the field, and the mechanical device or device from which water is sent out to the plant is called the outlet or dripper. The outflow of water from the emitter can be in the form of a drop, a bubble or a continuous small stream. Even the player can be a very small sprayer.

Equipment and parts for drip irrigation

Drip irrigation is required for polyethylene pipe products, irrigation pipes, irrigation strips and ad hoses.

The water source is the central control station (including pumping station and filtration station) where the pumping station itself includes the pump and its accessories and the filtration station uses either a cyclone or a sand filter (depending on the type of water source used, one of these two types of filters). Are cyclone or hydrocyclone filters for water wells, and sand filters for water storage pools), fertilizer tanks, mesh or disk filters (disk filters absorb smaller particles than mesh filters), main pipes, water pipes, pipes Side or side pipes (laterals), emitters and fittings required

Central Control Unit: It consists of devices that pump the pumped water after treatment and increase the fertilizer (if necessary) with precise control of the flow rate and pressure regulation into the main irrigation pipe.

• pump

• Relaxation Pool (if required)

• Hydrocyclone

• Sand filter

• Fertilizer tank

• Grid filter or disk filter

• Drip irrigation connections

Application of Drip Irrigation in Agriculture

Drip or topical irrigation refers to a variety of methods of pressurized irrigation, in which water is delivered directly to a small area near single plants by dropper or sprinklerers stationed along a water distribution line. In each fruit or vineyard there is one or more sprinklers for each tree.

For row crops (such as cauliflower, lettuce, pepper, cotton) and crops (alfalfa, legumes), the water dispenser is located close enough to the plant to provide the capillary force of soil water to the root range of each plant.

It is not common to use emitters for crops that are spread all over the farm due to the difficulty in humidifying the whole farm and the low price of these crops.

In fact, in a drip irrigation system, water is pumped to the ground near the root zone of the plant to soak a small area and depth of soil surface. The system was originally designed for a situation like fruit gardens where trees are too far apart. After drip irrigation proved to be a success for fruit trees, it was also applied to row crops.