List of Various Kinds of PE Fittings for Buyers

One of the most important advantages of polyethylene pipes compared to other types of pipes is its easy connectivity. Fittings are used in such cases as changing the angle of the pipeline route, changing the diameter, connecting the pipe parts and so on. In various applications, polyethylene pipes include screw joints, electro fusion joints and hand tools. read more about the bsp pe pipe fittings, 2 inch bsp fittings, pe100 pipe fittings, plastic bsp pipe fittings, hdpe threaded fittings, 100mm poly pipe fittings, poly pipe sizes chart and poly pipe fittings bunnings.

List of Various Kinds of PE Fittings for Buyers

BSP Threaded Plastic Pipe Fittings for Sale

BSP Threaded Plastic Pipe Fittings for Sale The BSP stands for “Standard British Pipe Issue”. BSP topics on piping systems are one of the most common in the world. Most plastic piping systems use a parallel type of BSP thread (often called BSPP), meaning that the diameter of the thread is the same for the entire length. BSPT threads (BSPTs) are sometimes found in metal pipe systems. With thick yarns, the diameter of the yarn is reduced to the tip.

BSP themes in imperialist sizes such as 2 “, 1”, 1 “, 1 1/4” and so on. This can often cause confusion in areas of the world where metric tube systems are used. Most metric plastic pipe systems use imperial yarn. Sometimes it may seem weird to install a 50mm tube with 1 ting thread, for example, but that’s true. In the world of plastic pipes, there is no such thing as 50mm yarn.

We will focus on BSPP topics in this article, as these are the types most commonly found in plastic pipe systems.

To determine the correct size of the BSP thread, you must measure and subtract the outer diameter of the thread. “So the thread whose diameter is actually measured is a thread of 6. Other. I know it confusing! To check that your thread is actually a BSP, the number of threads of yarn is 6% (6 mm) long. To multiply threads per inch, multiply this by four, and then refer to the diagram below (Note – For threads larger than 1 “, counting the number of nails is easier than doubling and doubling.

At our plastic pipe shop we often get in touch with people who have other issues with their plastic pipe system. These are usually NPT (National Pipe Thread), which is a North American standard. This is a connected topic and, despite what some say, these are not compatible with BSP topics. NPT often is the same as BSPP t but it is not. One remains and the other is parallel. Achieving a good seal, without the use of excessive rigidity, is very difficult and should be avoided.

What are the Various Types of Pipes and their Fittings?

Different types of pipe fittings in the piping system

There are different types of pipe fittings for plumbing purposes and for different purposes in plumbing systems. Pipe fittings in the piping system are used to join multiple pipes of different sizes or sizes to regulate the flow or measure the flow. They are made of various materials such as copper, iron, rice, PVC and so on.

Types of pipe fittings in the piping system

The various pipe fittings and their function are described below.

  • elbow
  • reducer
  • Tee type
  • Cross type
  • Pair
  • Unions
  • Adapters
  • First
  • plugin
  • Cap
  • valve

Elbow Pipe Fittings

The elbow is used to change the flow direction between the two tubes. Elbows are generally available with angles of 22.5 degrees, 45 degrees and 90 degrees. If the tubes are the same diameter, ordinary elbows are used, otherwise the elbows are lowered. Elbows are made of different materials. These are generally presented with feminine themes and we can repair them with butt or socket welding.


Reducer is a component of pipe fittings that reduces the size of the current from larger to smaller by reducing the pipe size. There are usually two types of reducers. One of the concentric reducers is that, like a cone, it is created by a gradual decrease around the tube, but in this case the air may accumulate and lead to cavitation. Another is anomalous reducers, which have an edge parallel to the connecting pipe which makes it impossible to accumulate air.

Tee type

Tee type fittings are T-shaped piping systems. With one inlet and two outlets, the outlets are arranged at 90 degrees to the main line (inlet). It can also be used to combine current from two inputs into a socket. They are also available in different materials and sizes. If the 3 sides of the T joints are similar in size, they are called equal even, otherwise they are called unequal Tee.

Cross type

Cross type fittings consist of 4 openings in 4 directions. These connections are connected when 4 pipes are in one place. As the temperature changes, these joints cause more stress in the pipe because they are at the center of the four connection points. Cross connections are commonly used for fire sprinkler systems.


Couplings are used to connect pipes of the same diameter. In case of pipe or leakage, connection is also useful. There are generally two types of connectors. Connect and compress compression. Compression joint is a common joint that connects between two tubes and prevents leakage by playing gaskets or rubber seals on both sides, otherwise the adhesive is made. It is easier to attach the displacement switch and include two tubes that are interconnected, the inner tube can slide somewhat. Therefore, we can resolve the long-lasting damaged connecting pipe with the displacement connection.


A union is a type of connection whose function is similar to a connection. But the couplings cannot be removed after removal, but in this case we can remove the union at any time. The unions include subjects ending with beads, males and females. Therefore, this is also useful for maintaining the purpose of the pipe.


If the tubes do not have a special end or a simple end, then attach the adapters to any of the males or females required. Adapters are usually used for copper and PVC pipes. Male adapters contain male threads and female adapters contain female threads. It is a simple adapter end that is glued or welded or welded to the end of a simple tube.


When the proper sizes are available, the proper connections are used, which is not suitable for our needs. Sometimes the size of the inlet pipe is larger than the outlet pipe in the t section and sometimes used by the Olets. There are many types of penis. Some important types of penis include:

  • Boil the first socket
  • String Elite
  • Your elbows
  • Notepad
  • Side Gear
  • broom
  • Olt flange
  • Olet pipe fittings


The plug is one of the plumbing components that is generally used to close the open pipe during inspection and repair. Branches usually contain male subjects.


The cap is a type of pipe fitting that functions like a plug, but the only difference is that the plug contains male threads and the cap contains female threads with screws on the male thread. These materials are available in various materials such as rubber, copper, steel, plastic and so on.

Valves in pipe fittings

Valves are components of a plumbing system that are used to stop or regulate the flow of fluid in its path. Depending on their application, different types of valves are also available.

What are the advantages of BSP pipe fittings?

What are the advantages of BSP pipe fittings?BSP stands for British Standard Pipe. The yarn, as defined by ISO 228, uses the Whitworth standard yarn, and is among the number of technical standards adopted internationally for connecting and sealing pipes and fittings. As a standard in piping and pipe fittings has been adopted almost worldwide.

BSP yarns have a side angle of 55 degrees, that is to say, the “v” angle formed by two strings. The bottom of the BSP thread is designed to sit on a chair (usually 30 degrees) and seal against it. If the application does not use a seal and is a “port”, it will be connected to the O-Ring washer, washer or washer. BSPP threads will not be properly sealed otherwise. Cone yarns are designed to be bonded to each other depending on the nature of the threads bonded. For these purposes a small amount of PTFE tape or the same sealant product should be used.

Properties of PE pipe fittings instead of metal fittiings

Polyethylene pipes are made of polyethylene raw materials with commercial grade PE80 and PE100. Polyethylene pipes are divided into two types of single wall and double wall pipes.

Single wall polyethylene pipes have simpler applications and are mostly used for water transfer and drainage in agriculture, protection of electrical and telecommunication cables, etc. Double walled polyethylene pipes are known in the market as carogite pipe and spiral pipe and are best suited for small and large water and sewage transmission networks.

Generally, polyethylene pipes are manufactured in 6 and 12 m branches with different diameters. The important thing about the size of the PE pipe and its use is that as the outer diameter of the pipe increases, the flow rate of the pipe outlet also increases; 30 liters per second and a 160 mm outer diameter polyethylene pipe has a discharge output of 73 liters per second.

What are the specifications of the PE pipe?

Whenever it comes to polyethylene pipes and their specifications, they mean all their mechanical and engineering features. For single and double wall polyethylene pipes, the specifications include the dimensions and size of the pipe and its inner and outer diameters. In addition, the nominal pressure, outlet discharge, hardness and strength of the pipes as well as the thickness of the polyethylene pipe are among the technical specifications. One of the most important technical issues for karogite pipes is their circular resistance. Circular resistance is a very important feature that determines how well the carogite pipe (with a specified diameter) can withstand working pressure along the pipeline and how well it fits in and fits.

What is the Importance of Knowing the Technical Specifications of PE?

In order to be able to properly install polyethylene pipes in a piping system, one must be fully aware of the technical and operational characteristics of these pipes. In fact, it is the specifications of the pipe that tell us which pipe and what dimensions can be used in a particular application (water supply, sewage or …).

For ethylene bridge pipes, they often provide a special table, which lists the size and size of the pipe, nominal pressure, connection method and operating pressure. For example, for karogite pipes, this table shows that if the pipe diameter is about 1600 to 2000 mm, the pipe must be bonded by extrusion welding; this table also shows that the maximum ring resistance How much pipe can be in the piping system.

Large exporters and suppliers of BSP pe Fittings

Large exporters and suppliers of BSP pe FittingsIran exported more than 5 million tonnes of BSP products last year, up about 30 percent from a year earlier. Steel products include all kinds of steel, beams, rebar, sheets, slabs and pipes, and steel profiles, if we include metals such as copper, lead, and so on. It is also planned to increase the export of Iranian steel products by 15 million tonnes up to 6 times more than current exports. Exports of steel industries are very lucrative and less complex than other commodities and there are endless markets for Iranian steel industries. However, due to the low export-to-production ratio in Iran, steel mills are not fully operational at present and as more traders enter the market, iron ore exports may soon increase. When a person wants to enter the steel export market, he or she needs to travel to the destination country first and look for a merchant, which is difficult. Transportation costs, accommodation and an interpreter also add to these difficulties. In addition, the probability of finding a reputable merchant is low. The Iron Center complex intends to pave the way for those interested in iron ore exports and will make no effort in this regard. The purpose of the pipe and profile export unit of this company is to supply and sell domestic manufactured product in global markets. We are going to introduce you to all the exporting conditions in this collection.

Which countries have cheap pipe and fittings to buy?

The first manufacturer of PE pipes

As mentioned in the History of Polyethylene Pipes, the first polyethylene pipes were manufactured in Germany in the 1950s. Therefore, Germany can be considered as the first producer of polyethylene pipes. This industry and technology has moved to other countries over time, so that today most developed and developing countries benefit from the production of these pipes. The United States is a leader among all the countries producing polyethylene pipes. It has been using these pipes and other polyethylene equipment for many years. So, the consumption of polyethylene in this country is increasing in volume.

Steel pipes have been the leading cause of leakage of more than 20 percent of the water consumed in the US over the past decades by researchers in various US states. Since a large percentage of these leaks occurred in the joints and joints of these pipes, the authorities decided to replace the pipes that require less quality in addition to being of high quality. Therefore, polyethylene pipes were chosen by experts to replace old steel and iron pipes. Replacing polyethylene pipes has many benefits for the US Water and Wastewater Organization, some of which are important:

  • Improved water supply system
  • Reduce the cost of traditional pipe repair
  • Extend the life of plumbing systems
  • Avoid wasting water and storing it
  • Reduce installation costs
  • And …

Manufacturer of polyethylene pipes in Iran

Today, Iran is also known as a producer of polyethylene pipes in the world. In fact, many companies and factories in Iran are operating in this field. These companies have contributed to the development of this industry in the country by exporting their polyethylene pipes and other products worldwide. So that the pipes produced in Iran are of high quality and have reached the international standards. Trend Polymer Company is also one of the manufacturers of polyethylene pipes, which produces laboratories equipped with high quality pipes.

Like many countries, Iran is facing a water shortage crisis. Therefore, in our country, as in America, we should think about it and remove the metal pipes over time. For example, pipes that are more resistant to metallic pipes can be easily removed from moisture and corrosion and prevent water leakage. It is clear that polyethylene pipes can be a good option to replace traditional metal pipes in water piping systems.

As mentioned in the previous section, these pipes have many advantages that have made them a viable alternative to traditional pipes. Polyethylene pipes are connected in two ways: screw and welding. Fittings such as traditional pipes do not easily rust and leak. Therefore, the connections of the PE pipes are well established and there will be no further leakage and loss of water.

Affordable prices for standard bsp pe fittings

Affordable prices for standard bsp pe fittings The price list for PE is not fixed and PE has different prices. Due to market volatility, prices of raw materials are changing day by day. As a result of these fluctuations, the price of polyethylene pipe will increase or decrease. The higher the volume of buyers’ orders, the lower the price of PE.

Timely delivery after clearing and full support is our top priority. Of course, finance has also tried to contribute to your satisfaction by presenting the day’s price chart.